2022-2024 RAM EZLYNK FLASHING INSTRUCTIONS
EZ LYNK FLASHING INSTRUCTIONS
IMPORTANT — READ ALL INSTRUCTIONS BEFORE FLASHING YOUR VEHICLE
IN A NUT SHELL:
PICK FILE TO FLASH -> CYCLE THE IGNITION ONE TIME -> BEGIN FLASH -> ONCE FLASH IS COMPLETED IF (PRND) IS NOT FLASHING AND RED SECURITY LIGHT IS NOT ON -> PRESS CONTINUE ON EZLYNK APP UNTIL DONE AND DO NO CYCLE THE IGNITION -> ABS INITIALIZATION RELEARN -> RADIO HUB RELEARN -> CLEAR CODES -> DRIVE .
(THE RADIO HUB RELEARN WILL CYCLE THE IGNITION FOR YOU, WITH OUT YOU EVER HAVING TO TOUCH THE IGNITION. ONCE THAT IS DONE YOU CAN START TRUCK AND CLEAR CODES AGAIN)
1. BEFORE FLASHING
-
Connect a battery charger to the passenger-side battery and verify both batteries have adequate voltage. Low voltage during flashing can cause ECM communication failures or potentially render the ECM inoperable.
-
Maintain a stable connection between your phone and EZ LYNK throughout the entire flashing process.
-
Disable CarPlay, Bluetooth, and any unnecessary wireless connections that could interfere with EZ LYNK. Keep the Wi-Fi connection required by EZ LYNK active.
-
DO NOT leave your phone or vehicle unattended while flashing.
-
ENSURE THE REQUIRED BYPASS CABLE IS INSTALLED CORRECTLY. Installation instructions are available on our website.
-
The throttle valve must be unplugged, and 2022+ trucks must have the OEM MAP sensor installed.
2. FLASHING PROCEDURE
-
Select and load the provided tuning file through the EZ LYNK application.
-
Follow the on-screen instructions and allow the flashing process to complete.
-
DO NOT disconnect EZ LYNK, interrupt the connection, or cycle the ignition during flashing or recovery unless specifically instructed by the application.
CRITICAL — VERIFY VEHICLE STATUS AFTER EVERY FLASH ATTEMPT
THIS APPLIES WHETHER THE FILE FLASHES SUCCESSFULLY, FAILS, OR TIMES OUT.
After every flashing attempt, verify the following:
-
Parking light: Confirm the parking light is NOT flashing or blinking on and off.
-
Security light: Confirm the red security light is NOT illuminated.
IF THE PARKING LIGHT IS FLASHING OR THE RED SECURITY LIGHT IS ON:
-
DO NOT CYCLE THE IGNITION OR ATTEMPT TO START THE VEHICLE AT ALL!!
-
DO NOT UNPLUG OR DISCONNECT EZ LYNK AT ALL!!
-
Keep the battery charger connected and maintain communication with the EZ LYNK application.
-
Continue following the application's on-screen prompts. Press Continue when prompted, or allow the application to enter recovery mode (DO NOT FUCKING CYCLE THE IGNITION)
-
Once recovery mode is available, follow the recovery procedure and load the appropriate recovery file or any other file.
-
Verify that the parking light has stopped flashing and the red security light is no longer illuminated before proceeding.
IMPORTANT: A completed flash message does not automatically mean the vehicle is ready to start. Always verify the parking and security lights before cycling the ignition.
3. AFTER FLASHING — REQUIRED RELEARN PROCEDURES
ONLY PROCEED ONCE THE FLASH HAS COMPLETED AND THE PARKING LIGHT IS NO LONGER FLASHING AND THE RED SECURITY LIGHT IS OFF. (STILL DO NOT FUCKING CYCLE THE IGNITION) SIMPLY CLICK CONTINUE AFTER FLASH HAS COMPLETED PROPERLY
Before starting the vehicle:
-
Scan the vehicle and CLEAR ALL DIAGNOSTIC TROUBLE CODES (DTCs).
-
Open the EZ LYNK Functions tab and perform any required module resets or relearns.
-
Perform the ABS Initialization / Traction Control / Brake System Reset, MANDATORY ! 1ST
-
Perform the Radio Hub Frequency Relearn, MANDATORY ! 2ND
-
Verify that all required relearns have completed and no unexpected warning lights remain before starting or driving the vehicle. If DEF light is still on please drive the vehicle and the light should clear after a few ignition cycles! Some codes may pop up on the EZLYNK but will not show a Check Engine Light on the dash. This is completely fine and will not cause issues. Only codes that appear on dash will need to be looked over if any. Common codes are P24E1 (Ammonia Sensor Circuit) & P0605 ( Internal Control Module Read-Only Memory (ROM) Error ) these codes will not affect the driving or reliability of the vehicle !
WARNING: Failure to properly complete the flashing recovery process, clear diagnostic codes, or perform required module relearns may result in warning lights, communication issues, starting problems, or other vehicle malfunctions.
4. TRANSMISSION TUNING INSTRUCTIONS
AISIN TRANSMISSION
-
If flashing Aisin TCM tuning, allow approximately 500 miles of normal stop-and-go driving for transmission shift adaptations to stabilize.
-
Avoid aggressive acceleration, heavy towing, and unnecessary high-load operation during the initial relearn period.
68RFE TRANSMISSION
-
68RFE-equipped trucks have engine and transmission tuning included within the same tuning file.
-
A separate TCM tuning file is NOT required.
-
Complete any required transmission Quick Learn procedure when applicable.
-
Allow approximately 500 miles of normal stop-and-go driving for transmission adaptations to stabilize.
-
Avoid aggressive driving, hard launches, and heavy-load operation during the relearn period.
TRANSMISSION WARNING: Failure to complete required transmission relearns or operating the vehicle aggressively before shift adaptations stabilize may result in harsh shifting, excessive clutch wear, slipping, or premature transmission damage.
5. CCV / DEF GAUGE SOTF
For vehicles equipped with CCV / DEF Gauge Switch-On-The-Fly tuning:
-
With the CCV connector unplugged or the switch in Position 5, the DEF gauge should display FULL.
-
The DEF gauge is used to indicate the selected tuning level when configured for this function.
6. CRUISE CONTROL SOTF
For vehicles equipped with Cruise Control Switch-On-The-Fly tuning:
-
Ensure Cruise Control is OFF.
-
Press and hold the Cruise Cancel button to display the currently selected tuning level.
-
The red lightning bolt indicator will flash to identify the selected power level.
Tune Level Indicators:
-
1 Flash = Level 1
-
2 Flashes = Level 2
-
3 Flashes = Level 3
-
4 Flashes = Level 4
-
5 Flashes = Level 5
Use the + or – buttons to increase or decrease the selected power level.
FINAL WARNING — DO NOT IGNORE
NEVER assume a flash was successful simply because the EZ LYNK application reports that the process has completed.
ALWAYS VERIFY:
-
Parking light is NOT flashing or blinking.
-
Red security light is NOT illuminated.
-
Required module recovery has completed.
-
Diagnostic trouble codes have been cleared.
-
Required Radio Hub and ABS relearns have been performed.
IF THE PARKING LIGHT IS STILL FLASHING OR THE RED SECURITY LIGHT IS ON, DO NOT CYCLE THE IGNITION, START THE VEHICLE, OR DISCONNECT EZ LYNK.
Continue following the application's recovery instructions until the vehicle has successfully recovered. If the issue persists, contact technical support before proceeding.
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN ECM/TCM COMMUNICATION ERRORS, NO-START CONDITIONS, INCOMPLETE FLASHING, OR VEHICLE DAMAGE.
I've made the parking-light and red-security-light verification a mandatory step after every flash attempt, including attempts the app reports as successful. I also separated recovery from normal post-flash procedures so customers know not to cycle the ignition or proceed with relearns while the vehicle is still showing a recovery-related warning.
https://www.instagram.com/p/Dfpyyg9tcgn/ PART 1